Machine news
You are here: Home » News » Machine news » car eating shredder,emr car shredder extreme car shredder

car eating shredder,emr car shredder extreme car shredder

Time:2018-10-31 Author:Hongyuan Machine

1200 waste car dismantling production line car shredder,
car eating shredder,emr car shredder extreme car shredder
 car dismantling equipment principle: the basic principle of hammer hitting Under the drive of high-speed and large-torque motor, the hammer on the main rotor turns to break into the cavity to be crushed, Through the space formed between the lining plate and the hammer head, the object to be crushed can be fully and effectively finely crushed in the crushing cavity, and the object to be crushed is torn into a crushed product of a specification. The crushed material is separated from the metal and non-metal by the air cyclone sorting system, and the whole system is equipped with a dust removing device to reduce the dust pollution hazard generated during the production process.
car eating shredder,emr car shredder extreme car shredder
The 1200 waste car dismantling production line is a high performance, high quality, environmentally friendly and low carbon product.
car eating shredder,emr car shredder extreme car shredder
Product advantages after shredding:

1. The material is convenient to transport after shredding, which can effectively reduce transportation cost and increase transportation efficiency;

2. The material after shredding is convenient for crushing and secondary treatment;

3. The shredded material is easier to store than the metal, which can save a lot of warehouse space;

4, shredded materials greatly facilitate the use and re-processing.

Shredder operation notes:
car eating shredder,emr car shredder extreme car shredder
Shredder operation precautions: First of all, from the operation point of view, after starting, the equipment is allowed to feed evenly and continuously when the equipment reaches normal operation. Pay attention to the motor, the speed of the thresher, the sound and the temperature of the bearing. When feeding, the operator should stand on the side of the feeding port, the sleeves of the clothes should be tight, and the mask and work cap should be worn. Pay attention to whether the grain has hard objects such as stones, trowels and tool screws when feeding, so as not to damage the equipment and cause accidents.

The shredder equipment is not allowed to hang, oil, clean and troubleshoot. There is also inspection, first check whether the rotor bearing box bolts can be loose, and then check whether the weight of each group of hammers can be symmetrically divided. Hammerhead broom, should lower the corresponding hammer head broom, the rotation speed is not enough, first check whether the voltage can be too low, and then check whether the wire number can be too small, and secondly, whether the excess material can be uneven.
car eating shredder,emr car shredder extreme car shredder
1. When the shredder blade is installed, the nut must be tight and the loose saw blade will slip during rotary cutting. Over-tightening the saw blade will cause internal damage or deformation and affect the cutting effect.

2. Regularly check the radial runout of the machine’s main shaft, and the swing to ensure the mutual fit between the shredder blade cuts.

3. The shredder blade The operator must bring protective equipment and check that the saw guard is in good condition before cutting.

4. The shredder blade should be idling for 30 seconds after it is installed smoothly, and then start cutting work after confirming that everything is normal.

5. The alloy head of the shredder has a sharp edge, so care must be taken to avoid damage to the alloy head during blade movement, installation and disassembly.

6. The shredder blade must be cleaned of debris on the spindle and flange before installation. The surface of the flange should be flat, clean and perpendicular to the axis.

Not only advanced machinery and equipment, but also satisfactory service:
pre-sale service:

To provide you with project design, process design, suitable for your machine equipment purchase plan, according to your special needs, design and manufacture products, training technical operators for you

In-sale service:

Work with you to complete the acceptance of the equipment, assist in the preparation of the construction plan and detailed process

After sales service:

The company sent technicians to the site to guide equipment installation, commissioning site and training operators.

Recommended news

Hongyuan Machinery    Address: Yong'an Road, Gongyi City, Henan, China  

Sservice Contact us

Hongyuan Machinery    Address: Yong'an Road, Gongyi City, Henan, China